Florida Supplement to the 2012 IRC
Note
1:
Throughout the document, change International Building Code to the
Note
2:
Criteria blocked in yellow indicate Florida specific language from the
2010 FBC.
R101.2 Change to read as shown:
R101.2
Scope. The provisions of the Florida Building Code, Residential,
shall apply to the construction, alteration, movement, enlargement,
replacement, repair, equipment, use and occupancy, location, removal and
demolition of detached one– and two–family dwellings and (townhouses) not more than three stories above grade plane in
height with a separate means of egress and their accessory structures.
Exceptions:
1-2 No change
3. Existing buildings
undergoing repair, alteration or additions, and change of occupancy shall
comply with the Florida Building Code,
Existing Building..
R101.2.1 The provisions of
Chapter 1, Florida Building Code, Building, shall govern the
administration and enforcement of the Florida Building Code, Residential.
CHAPTER 2: DEFINITIONS
Add the following definitions:
COMMISSION.
Means the Florida Building Commission created by this part.
HIGH
VELOCITY HURRICANE ZONE (HVHZ). This zone consists
of Broward and Dade counties.
MODULAR
HOME. Any residential unit, constructed to
standards promulgated by the Florida Building Commission, away from the
installation site, and which bears a Department of Community Affairs Insignia.
REGISTERED
TERMITICIDE. Product listed as registered for use
as a preventative treatment for termites for new construction by the Florida
Department of Agriculture and Consumer Services under authority of Chapter 487,
Florida Statutes.
CHAPTER 3, BUILDING PLANNING
R301.1 Change to read as shown:
R301.1 Application, Exception add to read:
EXCEPTION:
Buildings and structures located within the High Velocity Hurricane Zone shall
comply with Sections R302 to R324, inclusive and the provisions of Chapter R44 and section R406. In
addition, buildings and structures located in flood hazard areas established in
Table R301.2(1) shall comply with Sections R301.2.4 and R322.
R301.2.5 Add to read as follows:
R301.2.5
Structures seaward of a coastal control construction line.
Structures located seaward of the coastal construction control line shall be
designed to resist the predicted forces of a 100-year storm event in accordance
with Section 3109 of the
R318 PROTECTION
AGAINST SUBTERRANNEAN TERMITES. Revise to read as shown:
SECTION
R318
PROTECTION
AGAINST TERMITES
R318.1 Termite
Protection. Termite protection shall be provided by registered termiticides, including soil applied pesticides, baiting
systems, and pesticides applied to wood, or other approved methods of termite
protection labeled for use as a preventative treatment to new construction. See
§202, REGISTERED TERMITICIDE. Upon completion of the application of the termite
protective treatment, a Certificate of Compliance shall be issued to the
building department by the licensed pest control company that contains the
following statement: "The building has received a complete treatment for
the prevention of subterranean termites. Treatment is in accordance with rules
and laws established by the Florida Department of Agriculture and Consumer
Services."
R318.1.1 If soil treatment
used for subterranean termite prevention, the initial chemical soil treatment
inside the foundation perimeter shall be done after all excavation, backfilling
and compaction is complete.
R318.1.2If soil treatment is
used for subterranean termite prevention, soil area disturbed after initial
chemical soil treatment shall be retreated with a chemical soil treatment,
including spaces boxed or formed.
R318.1.3 If soil treatment is
used for subterranean termite prevention, space in concrete floors boxed out or
formed for the subsequent installation of plumbing traps, drains or any other
purpose shall be created by using plastic or metal permanently placed forms of
sufficient depth to eliminate any planned soil disturbance after initial
chemical soil treatment.
R318.1.4
If
soil treatment is used for subterranean termite prevention, chemically treated
soil shall be protected with a minimum 6 mil vapor retarder to protect against
rainfall dilution. If rainfall occurs before vapor retarder placement,
retreatment is required. Any work, including placement of reinforcing steel,
done after chemical treatment until the concrete floor is poured, shall be done
in such manner as to avoid penetrating or disturbing treated soil.
R318.1.5 If soil treatment is
used for subterranean termite prevention, concrete overpour
or mortar accumulated along the exterior foundation perimeter shall be removed
prior to exterior chemical soil treatment, to enhance vertical penetration of
the chemicals.
R318.1.6
If soil treatment is used for subterranean termite prevention, chemical soil
treatments shall also be applied under all exterior concrete or grade within 1
foot (305 mm) of the primary structure sidewalls. Also, a vertical chemical
barrier shall be applied promptly after construction is completed, including
initial landscaping and irrigation/sprinkler installation. Any soil disturbed
after the chemical vertical barrier is applied shall be promptly retreated.
R318.1.7
If a registered termiticide formulated and registered
as a bait system is used for subterranean termite prevention, §R318.1.1 through
§R318.1.6 do not apply; however, a signed contract assuring the installation,
maintenance and monitoring of the baiting system for a minimum of five years from the issue of the
Certificate of Occupancy shall be provided to the building official prior to
the pouring of the slab, and the system must be installed prior to final
building approval.
If the baiting system directions for use
require a monitoring phase prior to installation of the pesticide active
ingredient, the installation of the monitoring phase components shall be deemed
to constitute installation of the system.
R318.1.8
If a registered termiticide formulated and registered
as a wood treatment is used for subterranean termite prevention, Sections
R318.1.1 through R318.1.6 do not apply. Application of the wood treatment termiticide shall be as required by label directions for
use, and must be completed prior to final building approval.
R318.2
Penetration. Protective sleeves around piping penetrating
concrete slab-on-grade floors shall not be of cellulose-containing materials.
If soil treatment is used for subterranean termite protection, the sleeve shall
have a maximum wall thickness of 0.010 inch (0.25 mm), and be sealed
within the slab using a non-corrosive clamping device to eliminate the annular
space between the pipe and the sleeve. No termiticides
shall be applied inside the sleeve.
R318.3 Cleaning. Cells and cavities
in masonry units and air gaps between brick, stone or masonry veneers and the
structure shall be cleaned of all non-preservative treated or non-naturally
durable wood, or other cellulose-containing material prior to concrete
placement.
Exception:
Inorganic
material manufactured for closing cells in foundation concrete masonry unit
construction or clean earth fill placed in concrete masonry unit voids below
slab level before termite treatment is performed.
R318.4
Concrete bearing ledge. Brick, stone or other veneer shall be
supported by a concrete bearing ledge at
least equal to the total thickness of the brick, stone or other veneer
which is poured integrally with the concrete foundation. No supplemental
concrete foundation pours which will create a hidden cold joint shall be used
without supplemental treatment in the foundation unless there is an approved
physical barrier. An approved physical barrier shall also be installed from
below the wall sill plate or first block course horizontally to embed in a
mortar joint. If masonry veneer extends below grade, a termite protective
treatment must be applied to the cavity created between the veneer and the
foundation, in lieu of a physical barrier.
Exception:
Veneer supported by a structural member secured to the foundation sidewall in
accordance with ACI 530/ASCE 5/TMS 402, provided at least a 6 inch (152 mm)
clear inspection space of the foundation sidewall exterior exist between the
veneer and the top of any soil, sod, mulch or other organic landscaping
component, deck, apron, porch, walk or any other work immediately adjacent to
or adjoining the structure.
R318.5 Protection
against decay and termites, add text to read as shown:
R318.5
Protection against decay and termites. Condensate Lines, irrigation/sprinkler
system risers for spray heads, and roof downspouts shall discharge at least 1
foot (305 mm) away from the structure sidewall, whether by underground piping,
tail extensions or splash blocks. Gutters with downspouts are required on all
buildings with eaves of less than 6 inches (152 mm) horizontal projection
except for gable end rakes or on a roof above another roof.
R318.6 Preparation of building site and removal of debris.
Add text to read as shown:
R318.6 Preparation of
building site and removal of debris.
R318.6.1 All building sites
shall be graded to provide drainage under all portions of the building not
occupied by basements.
R318.6.2 The foundation and
the area encompassed within 1 foot (305 mm) therein shall have all vegetation,
stumps, dead roots, cardboard, trash and foreign material removed and the fill
material shall be free of vegetation and foreign material. The fill shall be
compacted to assure adequate support of the foundation.
R318.6.3 After all work is
completed, loose wood and debris shall be completely removed from under the
building and within 1 foot (305 mm) thereof. All wood forms and supports shall
be completely removed. This includes, but is not limited to: wooden grade
stakes, forms, contraction spacers, tub trap boxes, plumbing supports, bracing,
shoring, forms or other cellulose-containing material placed in any location
where such materials are not clearly visible and readily removable prior to
completion of the work. Wood shall not
be stored in contact with the ground under any building.
Revise
R322.1.7 to read as follows:
R322.1.7 Protection of water supply
and sanitary sewage systems.
New and replacement water supply systems shall be designed to minimize or
eliminate infiltration of flood waters into the systems in accordance with the
plumbing provisions of this code. New and replacement sanitary sewage systems
shall be designed to minimize or eliminate infiltration of floodwaters into
systems and discharges from systems into floodwaters in accordance with the
plumbing provisions of this code and in accordance with Chapter 64E-6, Florida Administrative Code,
Standards for Onsite Sewage Treatment and Disposal Systems. and Chapter
3 of the International Private Sewage Disposal Code.
R322.1.9 Manufactures homes. Revise to read as shown:
R322.1.9
Manufactured homes.
In addition to the applicable requirements of the state agency with
jurisdiction over installation of manufactured homes, installation of
manufactured homes in flood hazard areas is subject to the applicable
provisions of the local floodplain management ordinance.
R322.1.11
Structural seaward of a coastal
construction line. Add section to read
as shown:
R322.1.11
Structures seaward of a coastal construction line. In addition to the
requirements of this section, structures located in flood hazard areas and
seaward of the coastal construction line shall be designed to resist the
predicted forces of a 100-year storm event in accordance with Section
R3109 of the Florida Building Code,
Building, and the more restrictive provisions shall govern.
Revise to add R322.3.3.1 as a new
section.
R322.3.3.1
Pools. Pools
in coastal high-hazard areas shall be designed and constructed in conformance
with ASCE 24.
CHAPTER
4: FOUNDATIONS
Section R401.1 Application, revise
text to add exception 3 to read as follows:
3. Buildings and structures located within the High-Velocity Hurricane
Zone shall comply with the provisions of Chapter 44 and, as applicable, Section R322 in flood hazard areas.
CHAPTER
5 FLOORS
R501.1 Application. Change to read as follows:
R501.1 Application. The provisions of this chapter shall control the design and
construction of the floors for all buildings including the floors of attic
spaces used to house mechanical and/or plumbing fixtures and equipment.
Exception:
Buildings and structures located within the
High-Velocity Hurricane Zone shall comply with the provisions of Chapter 44.
Chapter
7 Wall Covering
Add exception to R701.1 as follows:
R701.1 Application. The
provisions of this chapter shall control the design and construction of the
interior and exterior wall covering for all buildings.
Exception: Buildings and
structures located within the High-Velocity Hurricane Zone shall comply with
the provisions of Chapter 44.
Add Section 704 to read as follows:
SECTION 704
INSPECTION FOR
TERMITES
In
order to provide for inspection for termite infestation, clearance between
exterior wall coverings and final earth grade on the exterior of a building
shall not be less than 6 inches (152 mm).
Exceptions:
1. Paint or decorative cementitious
finish less than 5/8 inch (17.1 mm) thick adhered directly to the masonry
foundation sidewall.
2. Access or vehicle ramps which rise to the
interior finish floor elevation for the width of such ramps only.
3. A 4-inch (102 mm) inspection space above
patio and garage slabs and entry areas.
4. If the patio has been soil treated for
termites, the finish elevation may match the building interior finish floor
elevations on masonry construction only.
5. Masonry veneers constructed in accordance with R318.4.
CHAPTER 8
ROOF-CEILING CONSTRUCTION
Add an exception to R801.1 as shown:
R801.1
Application. The provisions of this chapter shall
control the design and construction of the roof-ceiling system for all
buildings (see Section R301.2.1.1).
Exception: Buildings and
structures located within the High-Velocity Hurricane Zone shall comply with
the provisions of Chapter 44.
CHAPTER 9
ROOF ASSEMBLIES
Add exception to R901.1 as shown:
R901.1
Scope. The provisions of this chapter shall govern the design,
materials, construction and quality of roof assemblies.
Exception: Buildings and
structures located within the High-Velocity Hurricane Zone shall comply with
the provisions of Chapter 44.
Chapter 11, Energy Efficiency
SECTION N1101, GENERAL. Revise to read as shown:
N1101 Energy efficiency. The provisions of the
Florida Building Code, Energy
Conservation, shall govern the energy efficiency of residential
construction.
Chapter
26, General Plumbing Requirements
P2603.3 Breakage and corrosion.
Revise to read as shown:
P2603.3 Breakage and corrosion. Pipes passing through concrete or cinder walls and floors,
cold-formed steel framing or other corrosive material shall be protected
against external corrosion by a protective sheathing or wrapping or other means
that will withstand any reaction from lime and acid of concrete, cinder or
other corrosive material. Sheathing or wrapping shall allow for movement
including expansion and contraction of piping. Minimum wall thickness of
material shall be 0.010
inch (0.254 mm).
Exception: Sleeving is not
required for installation of CPVC into concrete or similar material
P2603.3.1
Penetration. Add text to read as shown:
P2603.3.1
Penetration. Protective sleeves around piping penetrating
concrete slab-on-grade floors shall not be of cellulose-containing materials.
If soil treatment is used for subterranean termite protection, the sleeve shall
have a maximum wall thickness of 0.010 inch, and be sealed within the slab
using a non-corrosive clamping device to eliminate the annular space between
the pipe and the sleeve. No termiticides shall be
applied inside the sleeve.
CHAPTER 44 45
REFERENCED STANDARDS
Add
the following standards:
AAMA American Architectural Manufacturers
Association
1827 Walden Office Square,
Suite 550
Schaumburg, IL 60173
203-98 Procedural Guide for the
Window Inspection and Notification System R4410.2.3.2.6
501—94 Methods of Test for Exterior
Walls
R4410.2.3.2.1
1302-76
Voluntary
Specifications for Forced-entry Resistant Aluminum Prime
Windows
R4410.2.3.2.1
1600/I.S. 7-00 Voluntary Specifications for Skylights
R4412.1.2
ACI American Concrete Institute
38800 Country Club Drive
Farmington Hills, MI 48331
117 Standard Tolerances for
Concrete Construction and Materials
R4405.2.2
301 Specifications for
Structural Concrete for Buildings R4405.2.2
315 Manual of Standard
Practice for Detailing Reinforced Concrete Structures R4405.2.2
347 Recommended Practice
for Concrete Formwork R4405.2.2, R4405.7.1.1
506 Recommended Practice
for Shotcreting
R4405.2.2
506.2 Building Code Requirements
for Masonry Structures R4405.2.2, R4405.11.1.2, R4405.11.8.1
530/530.1-11 Building Code Requirements for Masonry
Structures and Specifications
R404.1, R606.1,
for Masonry
Structures & Commentaries R606.1.1, R4403.7.8, R4407.5.1
AFPA
NDS—12 National Design Specification (NDS) for Wood
Construction with
R404.2.2, R502.2,
2001 Supplement
Table R503.1, R602.2,
R802.2, R4404.7.1.8.1,
R4409.1.4.7, R4409.2.4.1, R4409.6.17.2.1.3,
R4409.6.17.2.1.3, R4409.6.17.2.1.5
AFPA—05 Design Values for Wood Construction R4409.1.4.7,
R4409.6.17.2.2.1
AFPA—92 Wood Structural Design Data R4409.1.4.7
AFPA—9305 Working stresses for Joists and
Rafters Design
Values for Joists and Rafters
R4409.1.4.7
AFPA—2012 Span
Tables for Joists and Rafters R502.2.2, R802.2.2, R802.2.3,
R4409.1.4.7, R4409.4.1.1
T.R. No. 7—87 Basic
Requirements for Permanent Wood Foundation System PWF--07 Permanent
Wood Foundation (PWF)
Design Specification
R401.1, R4409.1.4.7
WCD
1—01 Wood Construction Data No.
1, Details for Conventional Wood Frame Construction R4409.1.4.7
WCD
4—03 Wood Construction Data
number 4, Plank and Beam Framing for
WCD
5—04 Wood Construction Data No.
5, Heavy Timber Construction Details R4409.1.4.7
WCD
6—0106 Wood Construction
Data No.6, Design of Wood Frame structures for Permanence R4409.1.4.7,
R4409.13.2.11
WFCM— 08 01 Wood
Frame Construction Manual for One- and Two-family Dwellings R301.2.1.1, R404.1.4,
R614.2.5, R614.3.1,
R802.2, R4409.1.4.7
AHA American
Hardboard Association
Referenced in code
reference
number Title
section number
A135.4—04 Basic Hardboard
Table R602.2(1), R4409.1.4.1
A135.5—04 Prefinished Hardboard Paneling
R702.5, R4409.1.4.1
A135.6—98 Hardboard Siding
Table R703.4, R4409.1.4.1
IB
Spec. No. 1 Recommended Product and
Application Specification-Structural
Insulating Roof
Deck
R4409.1.4.1
IB
Spec. No. 2 Recommended Product and
Application Specification-½ inch
Fiberboard
Nail-Base Sheathing
R4409.1.4.1
IB Spec. No. 3 Recommended Product and Application Specification-½ inch
Intermediate
Fiberboard Sheathing
R4409.1.4.1
AISC
American Institute of Steel Construction
Standard
Referenced in code
reference
number Title section
number
AISC
Detailing for Steel
Construction
R4408.1.3
AISC
Engineering for Steel Construction
R4408.1.3
AISC
Iron and Steel Beams 1873 to 1952
R4408.1.3
AISC
Serviceability Design Considerations for Low Rise
Buildings
R4408.1.3
AISC
Torsional Analysis of Steel
Members
R4408.1.3
AISC
Manual of Steel Construction, 2005,
Thirteenth edition,including Specification for Structural Steel
Buildings R4408.1.3
AISI
American Iron and Steel Institute
Standard
Referenced in code
reference
number Title section
number
AISI Design Manual for Structural
Tubing
R4408.1.3
AISI Designing Fire Protection for
Steel Trusses
R4408.1.3
AISI Designing Fire Protection for
Steel Columns
R4408.1.3
AISI Fire Resistant Steel Frame
Construction
R4408.1.3
AISI Fire Safe Structural Steel A
Design
R4408.1.3
AISI Specifications for Design of
Light Gage Cold Formed Stainless Structural Members R4408.1.3
AISI Specification for the
Criteria for Structural Application of Steel Cables for Buildings R4408.1.3
SGO4-5 Standard for Cold formed Steel
Framing Truss Design
R804.1.3
SGO4-6 Standard for Cold formed Steel
Framing Header Design R603.6
SGO3-3 Cold Formed Steel Design Manual
R4408.1.3
SG
971—96 Specification for the Design
of Cold Form Steel Structures
R4408.1.3
AITC American Institute of Timber
Construction
Standard Referenced
in code
reference
number Title
section number
AITC
104 Typical Construction
Details
R4408.1.4.2
AITC
106 Code of Suggested
Practices
R4409.1.4.2
AITC
108 Standard for Heavy Timber
Construction
R4409.1.4.2
AITC
109 Standard for Preservative
Treatment for Structural Glued Laminated Timber R4409.1.4.2
AITC
110 Standard Appearance
Grades for Structural Glued Laminate Timber R4409.1.4.2
AITC
112 Standard for Torque and
Groove Heavy Timber Roof Decking
R4409.1.4.2
AITC
113 Standard for Dimensions of Glued
Laminated Structural Members R4409.1.4.2
AITC
117 Standard Specification
for Structural Glued Laminated Timber of Softwood Species R4409.1.4.2
AITC
119 Standard Specifications
for Hardwood Glued Laminated Timber R4409.1.4.2
AITC A 190.1— 07 Structural Glued Laminated Timber R502.1.1.5, R602.1.1.2, R802.1.5, R4409.1.4.2, R4409.2.11
TR
No. 7 Calculation of Fire
Resistance of Glued Laminated Timber
R4409.1.4.2
ANSI American National Standards Institute
Standard Referenced
in code
reference
number Title
section number
A41.1 Building Code Requirements for
Masonry
R4407.2.1.1, R4407.4.2.8
A41.2 Building Code Requirements for
Reinforced Masonry
R4407.2.1.1
A42.1 Standard Specification for
Gypsum Plastering
R4411.2.1.1
A42.4 Standard Specification for
Interior Lathing and Furring
R4411.1
Z97.1— 09 Safety Glazing Materials Used in
Buildings—Safety Performance
Specifications and Methods of Test (Reaffirmed 1994) R308.3, R4403.7.3.6.3,
R4410.2.1.4, R4410.2.1.6
APA APA
The Engineered Wood Association
7011 South 19th
Standard
Referenced in code
reference
number Title
section number
V910 Plywood Folded Plate, Laboratory
Report 21
R4409.1.4.3
L350 Design/Construction Guide
Diaphragms R4409.1.4.3
PRP108 Performance Standards and Policies
for Structural Use Panels R4409.1.4.3, R4409.2.1.2
B840 303 Siding Manufacturing
Specifications R4409.1.4.3
E30—03 Engineered Wood Construction Guide
R803.2.3, R4409.1.4.3
H815 Plywood Design Specification
Design and Fabrication of All Plywood Beams R4409.1.4.3
S811 Plywood Design Specification
Design and Fabrication of Plywood Curved Panels R4409.1.4.3
S812 Plywood Design Specification
Design and Fabrication of Plywood Lumber Beams R4409.1.4.3
U813 Plywood Design Specification
Design and Fabrication of Plywood Stressed Skin Panels R4409.1.4.3
U814 Plywood Design Specification
Design and Fabrication of Plywood
Y510J Plywood Design Specification
R4409.1.4.3
ASCE American Society of Civil Engineers
Standard
Referenced in code
reference
number Title
section number
3—91 Specifications for the Design and
Construction of Composite Slabs and Commentary
on Specifications for the
Design and Construction of Composite Slabs R4405.2.3, R4408.1.3
5—
08 Building Code Requirements for
Masonry Structures R404.1, R606.1,
R606.1.1, R606.2.2,
R606.11.1,
R606.11.2.2.1, R606.11.2.2.2, R606.11.3.1, R4403.7.8
7—
10 Minimum Design Loads for Buildings and
Other Structures Figure 301.2(4),
R301.2.1.1, R301.2.1.1.2,
R301.2.1.4, Table
R611.3(1), Table R611.7.4, R4402.3.4,
R4403.1.3, R4403.4.1, R4403.4.2,
R4403.7.3.8, R4403.7.8, R4403.8,
R4403.9, R4403.10, R4403.12, Table R4403.15.4, R4403.16.1
8—02 Specifications for the Design of Cold
Formed Stainless Steel Structural members R4408.1.3
11—99 Guidelines for Structural Condition
Assessment of Existing Buildings R4405.2.3, R4406.1.2, R4408.1.3
32—01 Design and Construction of Frost
Protected Shallow Foundations R403.1.4.1, R4406.1.2
ASME American Society of Mechanical
Engineers
Standard
Referenced in code
reference
number Title
section number
B16.3— 2006 Malleable Iron Threaded Fittings Classes
150 and 300 Table P2904.6, Table R4413.2.7
B16.4— 2006
Gray iron Threaded Fittings Classes 125 and 250 Table P2904.6, Table R4413.2.7
B16.9—2003 Factory made Wrought Steel Buttwelding Fittings Table P2904.6, Table R4413.2.7
B16.11—2005 Forged Fittings, Socket welding and
Threaded Table P2904.6, Table R4413.2.7
B16.12—1998 Cast Iron Threaded Drainage
Fittings Table
P2904.6, Table R4413.2.7
B16.15— 2006 Cast Bronze Threaded
Fittings Table
P2904.6, Table R4413.2.7
B16.18—2001 (R2005) Cast Copper Alloy Solder Joint Pressure
Fittings Table P2904.6, Table R4413.2.7
B16.22—2001 (R2005) Wrought Copper and Copper Alloy Solder Joint
Pressure Fittings Table P2904.6, Table R4413.2.7
ASTM ASTM International
West
Standard
Referenced in code
reference
number Title
section number
A
6/A6M—04a Specification for General
Requirements for Rolled Structural Steel Bars,
Plates, Shapes and Sheet Piling
R4408.1.3
A
29/A29M Specification for
Steel bars, Carbon and Alloy, Hot Wrought, General
Requirements
R4404.11.1
A 53/A53M— 06a Specification for
Pipe, Steel, Black and Hot dipped, Zinc Coated Table 2904.4.1
Welded and Seamless
Table M2101.1, Table P2904.5, Table P3002.1, G2414.4.2, Table R4413.2.2
A 74— 09 Specification for Cast Iron Soil
Pipe and Fittings Table P3002.1,Table
P3002.2,
Table R4413.2.2, Table
R4413.2.3, Table R4413.2.4, Table R4413.2.5
A 82/A 82M -05a Specification for Steel Wire,
Plain for Concrete Reinforcement
R606.9.10
A
306 Carbon Steel Bars Subject to Mechanical
Property Requirements R4404.11.1
A 307—07b Specification for Carbon Steel
Bolts and Studs 60,000 PSI Tensile Strength
Table R611.9
A
325—94 Specification for
High Strength Bolts for Structural Steel Joints R4408.1.3
A
361 Specification
for Steel Sheet Zinc Coated (Withdrawn) R4409.6.17.1.1
A
416 - 99 Specification
for Steel
R4405.4.4.2
A
421/A421M—98 Specification for Uncoated
Stress Relieved Steel Wire for Prestressed
Concrete R4405.4.4.2
A
446 Specification
for Steel Sheet, Zinc Coated (Galvanized) by the Hot Dip
Process,
Structural (Physical) Quality
R4405.12.4.4
A
490—93 Specification for
Heat Treated Steel Structural Bolts
R4408.1.3
A
525 - 87 Specification for
Steel Sheet Zinc coated (Galvanized) Steel Wire
Table R606.9.10.1,
R4405.12.4.4, R4408.1.3, R4411.4.2, R4411.4.5.1, R4411.4.5.4, M1601.1.1
A 611 Standard Specification for
Structural Steel (SS), Sheet, Carbon, Coil Rolled R4404.10.1.5.3,
R4405.12.4.4
A 615/A 615M-09 Specification for
Deformed and Plain Billet Steel Bars for Concrete
Reinforcement R4405.2.2, R4405.2.4, R4405.4.4.6
A
617 Standard
Specification for Axle Steel Reformed and Plain Bars for
Concrete
Reinforcement R4405.4.4.6
A 653/A 653M-08 Specification for Steel Sheet, Zinc Coated
(Galvanized) or Zinc Iron
R505.2.1, R505.2.3,
Alloy Coated
(Galvanized) by the Hot Dip Process R603.2.1, R603.2.3, R804.2.1, R804.2.3,
Table 905.4.4,
Table R905.10.3, R4409.6.17.2.2.7
A 706/A 706M-09 Specification for Low Alloy Steel Deformed
and Plain Bars for
Concrete
Reinforcement
R404.4.6.1, R611.6.2, R4405.4.4
A
722/A 722M-98 Specification for Uncoated
High Strength Steel Bar for Prestressing
Concrete R4405.4.4.2
A
767/A 767M-00b Specification for Zinc Coated (Galvanized) Steel Bars for
Concrete
Reinforcement
R4405.4.4.6, R4405.8.5.5
A
775/A 775M-01 Specification for Epoxy
Coated Steel Reinforcing Bars
R4405.4.4.6
A 888- 09 Specification for Hubless
Cast Iron Soil Pipe and Fittings for
Table P3002.1, Table P3002.2,
Sanitary And
Storm Drain, Waste, and Vent Piping Application Table R4413.2.2,
Table R4413.2.3,
Table R4413.2.4, Table R4413.2.5, Table R4413.2.7
A 924/A924M-08a Standard Specification for General
Requirements for Steel Sheet, Metallic
Coated
by the Hot Dip Process
R4409.6.17.2.2.7
B 43—98 (2004) Specification for Seamless Red Brass
Pipe, Standard Sizes Table M2101.1, G2413.5.2,
Table P3002.1, Table P2904.4.1Table P2904.5, Table R4413.2.2
B 75— 02 Specification for Seamless Copper Tube Table M2101.1, Table P2904.4.1, Table
P2904.5,
Table P3002.1, Table P3002.2, Table R4413.2.2, Table R4413.2.3, Table R4413.2.4
B 88—03 Specification for Seamless Copper Water TubeTable M2101.1, G2414.5.2, Table P2904.4.1,
Table P2904.5, Table
P3002.1, Table P3002.2, Table
R4413.2.2, Table R4413.2.3, Table R4413.2.4
B 227—04 Specification for Hard drawn Copper
clad Steel Wire
R606.9.10
B 251—02e01 Specification for General Requirements for
Wrought Seamless Copper and Copper
Table M2101.1,
alloy Tube Table P2904.4.1, Table P2904.5, Table R4413.2.2, Table
R4413.2.3, Table R4413.2.4
B 302—07 Specification for Threadless
Copper Pipe, Standard Sizes Table M2101.1, Table
P2904.4.1,
Table
P2904.5, P2904.4, Table
R4413.2.2
B 306—09 Specification for Copper Drainage Tube
(DWV) Table M2101.1, Table P3002.1, Table
P3002.2,
Table R4413.2.2, Table R4413.2.4
B 370—09 Specification for Copper Sheet and Strip
for Building Construction Table R905.4.4
Table
R905.10.3, Table P2701.1
B695- 04
C4— 04e01 Specification for Clay Drain
Tile and Perforated Clay Drain Tile Table R4413.2.4, Table R4413.2.5
C5—03 Specification for Quicklime for Structural
Purposes R702.2, R4411.2.2.3
C 14—07 Specification for Concrete Sewer, Storm
Drain, and Culvert Pipe Table
P3002.2, Table R4413.2.4
C 28/C28M- 00(2005)
Specification for Gypsum Plasters
R702.2, R4411.2.2.2
C
31/C 31M-98Practice for Making and Curing Concrete Test Specimens in the Field
R4405.5.2.2.3,
R4405.5.2.3.2
C 33— 08 Specification for Concrete Aggregates R4405.4.2, R4405.4.2.2
C 34-03 Specification for Structural Clay Load
bearing Wall Tile Table R301.2(1), R4407.2.8.3.1
C 35-9501(2005) Specification for Inorganic Aggregates for
Use in Gypsum Plaster R702.2, R4411.2.2.1.1
C 36/C 36M-03 Specification
for Gypsum Wallboard R702.3.1, N1100.7, R4411.4.2
C 37/C 37M-01 Specification for
Gypsum Lath
R702.2, R4411.1.2
C
39—99ael Test Method for Compressive
Strength of Cylindrical Concrete Specimens R4405.5.2.2.3
C
42/C 42M-99 Test Method for Obtaining and Testing Drilled Cores and Sawed Beams
of Concrete R4405.5.2.4
C
52 Specification for
Gypsum Partition Tile or Block
R4407.2.9.3
C 55— 06e01 Specification for Concrete Brick R202, Table R301.2(1), R4407.2.4.2.2, R4407.2.4.3.3
C
56-96 (2001) Specification for
Structural Clay Nonload Bearing Tile
R4407.2.8.3.3
C
57 Specification for
Structural Clay Floor Tile
R4407.2.8.3.2
C 59/C 59M-00 (2006)
Specification for Gypsum Casting and Molding Plaster
R702.2
C 61/C 61M-00 (2006) Specification for Gypsum Keene’s Cement R702.2, R4411.1.2, R4411.2.2.4
C 62— 08 Specification for Building Brick (Solid
Masonry Units Made from Clay or Shale) R202,
C
67—03ae01 Test Methods of
Sampling and Testing Brick and Structural Clay Tile R905.3.5, R4407.2.4.2
C 76— 08
Specification for Reinforced Concrete Culver, storm Drain and Sewer Pipe
Table R4413.2.4
C 90—08 Specification for Load Bearing
Concrete Masonry Units Table
R301.2(1), R606.4,
R4407.2.7.2
C 91— 05 Specification for Masonry
Cement
R4412.2.2.6
C
94/C 94M -09 Specification for
Ready Mixed Concrete R404.1.2.3.2,
R611.5.1.1,
R4405.6.2
C
144—03 Standard Specification
for Aggregate for Masonry Mortar R4405.10.7.2, R4407.2.12.1.1
C 150— 07 Specification for
C
172—99 Practice for Sampling
Freshly Mixed Concrete
R4405.2.2.2
C 177-04 Test Method for Steady-State Heat Flux
Measurements and Thermal Transmission Properties by Means of the
Guarded-Hot-Plate Apparatus Table R301.2(1), N1110.AB.2.2
R4407.2.4.3.1
C 199-84(2005) Test Method for Pier Test for Refractory
Mortar R1001.9, R1003.5, R1003.8, R4405.4.1
C
206-84(1997) Specification for
Finishing Hydrated Lime
R4411.2.2.3
C
212—00 Specification for
Structural Clay Facing Tile
R4407.2.8.2
C 216— 07a Specification for Facing Brick (Solid
Masonry Units Made from Clay or Shale) R202,
Table
R301.2(1), R4407.2.4.3.1
C 236-89 (1993el) Test Method For Steady-State
Thermal Performance of Building
Assemblies by Means
of a Guarded Hot Box. Appendix
G C2.2.2
C 270— 08a
Specification for Mortar for Unit Masonry
R607.1, R4407.2.12.1
C
330—99 Specification for
Lightweight Aggregates for Structural Concrete R4405.4.2
C
332—99 Standard Specification
for Lightweight Aggregates for Insulation Concrete R4405.12.4.6
C 425-04 Specification for Compression
Joints for Vitrified Clay Pipe and FittingsTable
P3002.2, P3003.3.5
C 428-05(2006) Specification for Asbestos Cement Nonpressure Sewer pipe Table R4413.2.3, Table R4413.2.4
C
471M-01 Standard Test Methods for
Chemical Analysis of Gypsum and Gypsum Products R4407.2.9.2,
R4407.2.9.3
C
472—99 Specification for Standard
Test Methods for Physical Testing of Gypsum,
Gypsum Plasters and
Gypsum Concrete
R4407.2.9.2, R4407.2.9.3
C
473—00 Test Method for Physical
Testing of Gypsum Panel Products R4407.2.9.2, R4407.2.9.3
C 475/C475M—02(2007) Specification
for Joint Compound and Joint Tape for Finishing Gypsum Wallboard R702.3.1,
R4411.4.2
C
494/C 494M-99 Standard Specification for Chemical Admixtures for Concrete R4405.12.4.4
C
495-99a Standard Test Method for
Compressive Strength of Lightweight Insulating Concrete R4405.12.1.1,
R4405.12.1.2,
R4405.12.1.3
C
508—00 04 Specification for Asbestos
Cement Underdrain Pipe Table R4413.2.5
C
509-00
Elastomeric Cellular Preformed Gaskets and Sealing
Material R4410.2.3.4
C 516-02 Vermiculite Loose
Fill Thermal Insulation Appendix
G Table B1.2.3
C
518-04 Test Method for Steady-State Thermal Transmission Properties by Means of
the Heat Flow Meter Apparatus
N1110.AB.2.2
C 549-06 Perlite Loose
Fill Insulation Appendix
G Table B-1.2.3
C 578- 08b Rigid, Cellular
Polystyrene Thermal Insulation Appendix G Table B-1.2.3
C 595— 08a Specification for Blended Hydraulic
Cement
R4405.4.1
C
618—99 Specification for Coal Fly
Ash and Raw or Calcined Natural Pozzolar
for Use
as a Mineral Admixture in Concrete
R4405.12.4.4
C 645— 08a Specification for Nonstructural Steel
Framing Members R702.3.3, R4409.6.17.1.3, R4411.4.2,
R4411.4.5.1,
R4411.4.5.4
C 652—09 Specification for Hollow Brick (Hollow
Masonry Units Made from Clay or Shale) R202,
Table
R301.2(1), R4407.2.4.3.1
C 665-06 Mineral-Fiber
Blanket Thermal Insulation for Light Frame
Construction and
Manufactured Housing Appendix
G Table B-1.2.3
C 685 - 07 Specification for
Concrete Made by Volumetric Batching and Continuous Mixing R4405.6.2.2
C 700- 07a Specification for Vitrified Clay Pipe, Extra
Strength, Standard Strength, and Perforated Table P3002.2,
R4409.6.17.1.3,
Table R4413.2.4, Table R4413.2.5
C 727-01 Standard Practice
for Installation and Use of Reflective
Insulation in
Building Constructions. Appendix
G Table B-1.2.3
C 739-05b Cellulosic Fiber (Wood-Base)
Loose-Fill Thermal Insulation Appendix
G Table B-1.2.3
C 764-06a Mineral Fiber Loose-Fill Thermal
Insulation Appendix
G Table B-1.2.3
C
794—01 Test Method for Adhesion in
Peel of Elastometric Joint Sealants
R4410.6.4
C
796—97 Standard Test Method for
Foaming Agents for Use in Producing
Cellular Concrete
Using Performed Foam R4405.12.1.1, R4405.12.1.2,
R4405.12.1.3, R4405.12.4.6
C
864-05
Dense Elastomeric Compression Seal Gaskets, Setting Blocks, and
Spacers R4410.2.3.4
C
869 Specification for Foaming
Agents Used in Making Performed Foam for Cellular Concrete R4405.12.4.6
C 887- 05
Specification for Packaged, Dry, Combined Materials for Surface Bonding
Mortar R406.1
C 920 - 08
Specification for Elastomeric Joint Sealants …………………... R4410.6.4, R613.8.1
C 926-06 Specification for Application of Portland
Cement Based Plaster R202, R703.6.2.1, R4411.3.1.1,
R4411.3.1.4
C 1015-06 Standard Practice for Installation
of Cellulosic and Mineral Fiber
Loose-Fill Thermal
Insulation Appendix
G Table B-1.2.3
C 1029-08 Specification
for Spray-Applied Rigid Cellular Polyurethane
Thermal Insulation Appendix G Table B-1.2.3
C
1036-01 Specification for Flat Glass
R4410.2.1.2
C
1048-04 Specification for Heat
Treated Flat Glass—Kind HS, Kind FT Coated 7 Uncoated Glass R4410.2.1.5
C
1053-00 Specification for
Borosilicate Glass Pipe and Fittings for Drain, waste and Vent
(DWV) Applications
Table R4413.2.2
C
1077 Standard Practice for
Laboratories Testing Concrete and Concrete Aggregates for
Use in Construction and
Criteria for Laboratory Evaluation R4405.2.4, R4405.4.6
C 1158-05 Standard Practice for Use and
Installation of Radiant Barrier Systems
N1104.A.3,
(RBS) in Building
Construction Appendix
G Table B-1.2.3,
Appendix
G Table C4.2.1.4
C 1224-03 Reflective Insulation for Building
Applications Appendix
G Table B-1.2.3
C 1281- 03 Standard Specification for Preformed Tape
Sealants for Glazing Applications ………………………………………..………… R613.8.1.8.1
ASTM C 1289-08 Faced Rigid Cellular Polyisocyanurate Thermal Insulation Board Appendix G Table B-1.2.3
ASTM C 1313-05 Sheet Radiant Barriers for
Building Construction Applications N1104.A.3,
Appendix
G Table B-1.2.3, Appendix G Table C4.2.1.4
ASTM C 1320-05 Standard Practice for
Installation of Mineral Fiber Batt and
Blanket Thermal
Insulation for Light-Frame Construction Appendix
G Table B-1.2.3
ASTM C 1321-04 Standard Practice for
Installation and Use of Interior Radiation
N1104.A.3
Control Coating
Systems (IRCC) in Building Construction Appendix
G Table B-1.2.3
Appendix
G Table C4.2.1.4
ASTM C 1371-04a Test Method for Determination of Emittance of Materials Near N1104.A.3, N1104.4
Room Temperature
Using Portable Emissometers. Appendix G Table B-1.2.3,
Appendix
G Table C4.2.1.4
ASTM
C 1549-04 Standard Test
Method for Determination of Solar Reflectance Near
Ambient Temperature
Using a Portable Solar Reflector N1104.A.4
D
25-99 Standard
Specification for Round Timber Piles
R4404.7.1
D 41- 05 Specification for Asphalt Primer Used
in Roofing, Dampproofing, Table R905.9.2,
and Waterproofing Table R905.11.2, R4402.3.2.3.2, R4402.6.6.2.4, R4402.8.6,
R4402.10.6, R4402.10.14.1
D 43-00 (2006) Specification for Coal Tar
Primer Used in Roofing, Damproofing and
Waterproofing Table R905.9.2, R4402.6.6.2.4, R4402.8.6, R4402.10.6,
R4402.10.14.2
D
92 Standard Test
Method for Flash and Fire Points by
D 226- 06
Specification for Asphalt saturated (Organic Felt) Used in Roofing
and R703.2, R703.9.1,
Waterproofing
R905.2.2,
R905.2.3, R905.2.7,
R905.4.3, R905.5.3, R905.6.3, R905.8.4,
R905.8.10.1, Table 905.9.2, R4402.7.4
D
256-03 Test Methods for
Determining Izod Pendulum Impact Resistance of
Plastics R4412.1.2
D 312-00 (2006) Specification for Asphalt Used in Roofing R905.9.2, R4402.8.4, R4402.10.14.1
D
412-98a(2002)el Test Methods for
Vulcanized Rubber and Thermoplastic Elastomers Tension R4410.6.4
D
624-00el Test Methods for
Tear Strength of Conventional Vulcanized Rubber and
Thermoplastic Elastomers
R4410.6.4
D
635-03 Test Methods
for Rate of Burning and/or Extent & Time of Burning of Plastics
in a Horizontal Position
R4412.1.2
D
1079-02 Standard
Terminology Relating to Roofing, Waterproofing and Bituminous Materials
R4402.2.1
D
1143-81 (1994) e01 Test Method for Piles
Under Static Axial Compressive Load R4404.13.1.7
D
1167 Methods of
Testing Asphalt Base Emulsions for Use as Protective
Coatings for
Built Up Roofs
R4402.12.6.5.2
D
1556 Standard Test
Method for Density of Soil In Place by the Sandcone R4404.4.3.2
D 1557-00 Test Method for Laboratory
Compaction Characteristics of Soil Using
Modified Effort [56,000
ft lb/ft3 (2700 kN m/m3)] R4404.4.3.2
D
1586-99 Specification for
Penetration Test and
D
1621 – 04a Standard
Test Method for Compressive Properties of Rigid Cellular Plastics
4402.12.6.5.2.17.1
D 1622 -08 Standard Test Method for Apparent Pensity of Rigid Cellular Plastics R4402.12.6.5.2.17.2
D 1623 -03 Standard
Test Method for Tensile and Tensile Adhesion Properties of
Rigid Cellular
Plastics
R4402.12.6.5.2.17.3
D 1693- 08 Test Method for Environmental Stress
cracking of Ethylene Plastics Table M2101.1
D
1760 Standard
Specification for Pressure Treatment of Timber Products Table
R4404.7
D
1761-88(2000)el Test Methods for
Mechanical Fasteners in Wood
R4409.1.4.4
D
1861 Specification
for Homogenous Bituminized Fiber Drain Sewer Pipe
(Withdrawn 1992—Replacement)
P3002.2
D 1863- 05 Specification for Mineral Aggregate
Used in Built up Roofs Table R905.9.2,
Table R906.3.2,
R4402.8.12.1
D
1929-96(2001)el Test Method for
Determining Ignition Temperatures of Plastics R4412.1.2
D 2126 -04 Standard Test Method for Response
of Rigid Cellular Plastics to Thermal and
Humid Aging
R4402.12.6.5.2.17.4
D
2240—03 Test Method for Rubber
Property Durometer Hardness
R4410.6.4
D 2464—06 Specification for Threaded Poly (Vinly Chloride) (PVC) Plastic Pipe Fittings,
Schedule 80
Table P2904.6, Table
R4413.2.7
D 2466—06 Specification for Poly (Vinyl Chloride)
(PVC) Plastic Pipe Fittings, Schedule 40 Table P2904.6,
Table R4413.2.7
D 2467—06 Specification for Poly (Vinyl Chloride)
(PVC) Plastic Pipe Fittings, Schedule 80 Table P2904.6,
Table R4413.2.7
D 2468—96a Specification for Acrylonitrile
Butadiene Styrene (ABS) Plastic Pipe Fittings,
Schedule 40
Table P2904.6, Table
R4413.2.5, Table R4413.2.7
D
2565—99 Practice for Xeon Arc
Exposure of Plastics Intended for Outdoor Applications R4412.1.2
D 2609—02(2008) Specification for Plastic Insert
Fittings for Polyethylene (PE) Plastic Pipe Table P2904.6,
Table R4413.2.7
D 2626—04 Specification for Asphalt saturated and
Coated Organic Felt Base Sheet Used
in Roofing R905.3.3,
Table R905.9.2, R4402.7.4
D 2661—08 Specification for Acrylonitrile Butadiene
Styrene (ABS) Schedule 40 Plastic Drain,
Table P3002.1,
Waste, and Vent Pipe and
Fittings Table P3002.2, Table
R4413.2.2, Table R4413.2.3, Table R4413.2.4
D 2665—09 Specification for Poly
(Vinyl Chloride) (PVC) Plastic Drain, Waste, and Table P3002.1,
Vent
Pipe and Fittings Table P3002.2, Table R4413.2.2, Table R4413.2.3, Table R4413.2.4
D
2677-71(1976) Method of Test lightability of Barbecue Briquettes (withdrawn no
replacement,
1985)
Table R4413.2.4.3
D
2729—03 Specification for Poly (Vinly Cloride)(PVC) Sewer Pipe
and Fittings Table R4413.2.5
D 2751— 05
Specification for Acrylonitrile Butadiene Styrene (ABS) Sewer Pipe and
Fittings Table P3002.2,
Table R4413.2.4
D
2797-85(1999) Standard Practice for
Preparing Coal Sampler for Microscopical Analysis by
Reflected Light
Table R4413.2.4
D
2842 Standard Test
Method for Water Absorption of Rigid Cellular Plastics R4402.12.6.5.2.17.6
D
2843—99 Test Method for Density of
Smoke from the Burning or Decomposition of Plastics Table R4413.1.2
D
2856 Standard Test
Method for Open Cell Content of Rigid Cellular Plastics by
the Air Pycnometer
R4402.12.6.5.2.17.5
D 2898-04 Test Methods for Accelerated Weathering of
Fire retardant treated Wood
for Fire Testing R802.1.4.1, R802.1.4.3, R902.2, R4409.1.4.4, R4409.14.4, R4409.16.1
D
2922 Standard Test
Method for Density of Soil and Soil Aggregate In Place by
Nuclear
Methods (Shadow Depth) R4404.4.3.2
D 2949—01a(2008) Specification for 3.25 in. Outside Diameter
Poly (Vinyl Chloride) (PVC) Plastic Table P3002.1,
Drain, Waste,
and Vent Pipe and Fittings
Table P3002.2, R4402.5.1,
Table R4413.2.2,
Table R4413.2.3
D
3018 Specification for Class A Asphalt
Shingle Surfaced with Mineral Oravies
R4402.12.6.5.1
D 3034— 08 Specification for Type PSM Poly (Vinyl
Chloride) (PVC) Sewer Pipe and Fittings
Table
P3002.2, R4413.2.4
D 3201-08a Test Method for Hygroscopic
Properties of Fire retardant Wood and Wood base
Products R802.1.4.4, R4409.1.4.4, R4409.14.5
D
3441 Static Cone
Soundings
R4404.18.3.3
D 3462- 09 Specification for Asphalt Shingles Made From
Glass Felt and Surfaced
with Mineral
Granules
R905.2.4, R4402.12.6.5.1
D
3498-03 Specification for
Adhesives for Field Gluing Plywood to Lumber Framing
for Floor Systems
R4409.1.4.4, R4409.9.1.5
D 3679-09 Specification for
Rigid Poly (Vinyl Chloride) (PVC) Siding
Table R703.4, R703.11,
R703.11.1
D
3746-85(1996)e1 Test Methods for Impact Resistance of Bitumanous
Roofing Systems R4402.4.2.4
D
3787-01 Test Method for
Bursting Strength of Textiles Constant Rate of Traverse (CRT)
Ball Burst Test
R4101.17.1.15
D
4272—99 Test Method for Total
Energy Impact of Plastic Films by Dart Drop R4402.4.2.4
D
4402 Viscosity Determinations of
Unfilled Asphalt Using the
D
5034—95 Test Method for
Breaking Strength and Elongation of Textile Fabrics (Grab Test) Specifications
for Adhesives
for Field Gluing Plywood to Lumber Framing for Floor Systems R4101.17.1.15
D 6083—05e01 Specification for Liquid Applied
Acrylic Coating Used in Roofing Table R905.9.2,
Table
R905.11.2, Table R905.15.2, R4402.12.6.2
D 6380— 03 (2009) Specification for Asphalt Roll Roofing
(Organic Felt) R905.2.8.2, R905.3.3
ASTM D 6509-00 Specification for Atactic
Polypropylene (APP) Modified Bituminous Base Sheet Materials Using Glass Fiber
Reinforcements ……………………….Table R905.11.2
D6757- 07 Standard Specification for
Underlayment Felt Containing Inorganic Fibers
Used in
Steep-Slope Roofing
R905.2.2, R905.2.3, R905.2.7
D7158- 07 Standard Test Method for Wind
Resistance of Sealed Asphalt Shingles (Uplift
Force/Uplift
Resistance Method)
R905.2.6.1, Table R905.2.6.1
E 84- 09 Test Method
for Surface Burning Characteristics of Building Materials N1110.AB.3.0.7
R202, R314.3, R314.5.8,
R314.5.10, R315.3,
R315.4, R316.1, R316.2, R802.1.4, M1601.16, M1601.3.7
R4409.1.4.4, R4409.14.1, R4412.1.2, R4412.1.3.1.1, R4412.1.3.1.4, R4412.1.3.2.4.5,
E 96/E96M-05 Test Method for Water Vapor
Transmission of Materials M1411.4, M1601.3.4, R202,
R804.4,
R4402.12.6.5.2.17.7,
R4409.13.3.2.5
E 108—07a Test Methods for Fire Tests of Roof
Coverings R902.1,
R902.2, R4402.2.1,
R4402.5.1,
R4402.12.1.2, R4409.16.1
E 119-08a Test Methods for Fire
Tests of Building Construction and Materials
R314.1.2, R314.4,
R317.1, R317.3.1
R4412.1.2, R4412.1.3.2
E 136— 09
Test Method for Behavior of Materials in a Vertical Tube Furnace at 750
Degree C R202
E
152—95 Methods of Fire Tests of
Door Assemblies
R314.3, R4412.1.3.1.4
E
163 Methods of Fire Tests for Window
Assemblies (Withdrawn) R4407.4.2.12.8
E 283-04 Standard Test Method for
Determining the Rate of Air Leakage through Exterior Windows, Curtain Walls and
Doors Under Specified Pressure Differences Across the Specimen R806.4, , R4409.13.3.2.5,
E 330-02 Test Method for Structural
Performance of Exterior Windows, Curtain Walls, and
Doors by Uniform
Static Air Pressure Difference R613.3, R613.4.1, R4410.6.4, R4410.6.6.1
E 331—00(3009) Test Method for Water Penetration of
Exterior Windows, Skylights, Doors and
Curtain Walls by
Uniform Static Air Pressure Difference R613.4, R4410.6.4
E 903-96 Test Method for
Solar Absorptance, Reflectance, and Transmittance
of Materials Using
Integrating Spheres N1104.A.4, Appendix G C4.2.1.5
E
1300—04e01 or 98 (HVHZ) Practice for Determining Load Resistance of Glass in
Buildings . . . . . . . . . . . . . . .
. . . . R4410.2.2
F 405— 05 Specifications for Corrugated
Polyethylene (PE) Tubing and Fittings Table R4413.2.5
F 409—02(2008) Specification for Thermoplastic
Accessible and Replaceable Plastic Tube and
Tubular
Fittings
Table P2701.1, P2702.3, Table R4413.2.7
F 437— 06
Specification for Threaded Chlorinated Poly (Vinyl Chloride) (CPVC)
Plastic
Pipe Fittings, Schedule 80
Table P2904.6, Table
R4413.2.7
F 438—04 Specification for Socket type
Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic
Pipe Fittings,
Schedule 40
Table P2904.6, Table
R4413.2.7
F 439— 06 Specification for Socket type
Chlorinated Poly (Vinyl Chloride) (CPVC) Plastic
Pipe Fittings,
Schedule 80
Table P2904.6, Table
R4413.2.7
F 628— 08 Specification for Acrylonitrile Butadiene
Styrene (ABS) Schedule 40 Plastic Waste
and Vent Pipe with a Cellular Core Table P3002.1, Table P3002.2, Table R4413.2.2, Table R4413.2.3, Table R4413.2.4
F 891—07 Specification for Coextruded Poly (Vinyl
Chloride) (PVC) Plastic Pipe with a
Table P3002.1,
Cellular Core Table P3002.2, Table R4413.2.2, Table R4413.2.3, Table R4413.2.4, Table
R4413.2.5
F 1346-91(2003) Performance Specification for Safety Covers
and Labeling Requirements for
Swimming
Pools, Spas and Hot Tubs
R202
F 1554—07aStandard Specifications
for Anchor Bolts Steel 36, 55 and 105 ksi Yield
Strength Table R4413.2.5
G
26—77 Practice for Operating
Light Exposure Apparatus (Xenon Arc Type) With and
Without Water for
Exposure of Nonmetallic Materials (Withdrawn) R4412.1.2
G
53—96 Practice for Operating
Light and Water Exposure Apparatus (Fluorescent UV
condensation type)
for Exposure of Nonmetallic Materials R4401.17.1.15
G
60 Standard Practice
for Conducting Cyclic Humidity Exposures R4409.6.17.2.2.8
G
85 Standard Practice
for Modified Salt Spray (Fog) Testing R4402.6.5
AWPA American Wood Preservers’
Association
Standard
Referenced
in code
reference
number Title
section number
C2—01 Lumber, Timbers, Bridge Ties and Mine
Ties — Preservative Treatment
by Pressure Processes R319.1,
R323.1.7, Table R905.8.5, R4409.1.4.5
C3—99 Piles — Preservative Treatment by
Pressure Processes R319.1, R323.1.7,
R4404.7.1.3, R4409.1.4.5
C4—99 Poles — Preservative Treatment by
Pressure Processes R319.1, R323.1.7,
R4409.1.4.5
C5—03 Posts—Pressure Treatment by
Pressure Processes R4409.1.4.5
C6—99 Crossties and Switch Ties
Preservative Treatment by Pressure Processes R4409.1.4.5, R4409.21.9
C7—96 Western Red Cedar, Northern White
Cedar &
Treatment of Incised
Pole Butts by the Thermal process (Withdrawn) R4409.1.4.5
C8—96 Western Red & Alaska Yellow
Cedar Poles Preservative Treatment by the Full
Length Thermal process
(Withdrawn) R4409.1.4.5
C9—03 Plywood — Preservative Treatment by
Pressure Processes R319.1, R323.1.7, R4409.1.4.5
C10—96 Lodgepole
Pine Poles Preservative Treatment by the Full Length Thermal Process
R4409.1.4.5
C11—01 Wood Blocks for Floors &
Platforms Pressure Treatment by the Pressure Process R4409.1.4.5
C14—03 Wood for Highway Construction
Pressure Treatment by the Pressure Process R4409.1.4.5
C16—03 Wood used on Farms Pressure Treatment
R4409.1.4.5
C18—99 Standard for Pressure Treated
Material in Marine Construction R319.1, R323.1.7, R4409.1.4.5
C20—99 Structural Lumber—Fire retardant
Treatment by Pressure Processes R4409.1.4.5
C22—96 Lumber and Plywood for Permanent Wood
Foundations— Preservative Treatment
by Pressure Processes R319.1,
R323.1.7, R402.1.2, R504.3, R4409.1.4.5
C23—03 Round Poles and Posts Used in
Building Construction— Preservative Treatment
by Pressure Processes R319.1,
323.1.7, R4409.1.4.5
C25—03 Sawn Crossarms
Pressure Treatment
R4409.1.4.5
C26—57 Crossarms
Non Pressure Treatment
R4409.1.4.5
C28—99 Standard for Preservative Treatment
by Pressure Process of Structural Glued
Laminated Members and
Laminations Before Gluing R4409.1.4.5
C29—01 Lumber to be used for the Harvesting
Storage and Transportation of Food Stuffs
Preservative Treatment
by Pressure Processes R4409.1.4.5
M1—01 Standard for the Purchase of Treated
Wood Products
R4404.7.1.4
M2—01 Standard for the Inspection of Wood
Products Treated with Preservatives R4404.7.1.4
M4—08 Standard for the Care of
Preservative treated Wood Products R4404.7.1.4, R4409.1.4.5
AWS
American Welding Society
Standard
Referenced in code
reference number Title section
number
B2.1 Standard Welding Procedure and
Performance Qualification
R4408.1.3
C5.4 Recommended Welding Practice for
Stud Welding
R4408.1.3
D1.1 Structural Welding Code Steel
R4408.1.3
D1.2 Structural Welding Code Aluminum
R4406.1.3
D1.3 Structural Welding Code Sheet
Metal
R4408.1.3
D1.4 Structural Welding Code
Reinforcing Steel R4405.4.4, R4405.8.4.8, R4407.2.1.1,
R4408.1.3
D9.1 Specification for Welding of
Sheet Metal
R4408.1.3
D10.9 Standard for Qualification of
Welding Procedures and Welders for Piping and Tubing R4408.1.3
AWWA American Water Works Association
Standard
Referenced in code
reference
number Title
section number
C110/A21.1.10—03 Standard for Ductile iron and
Gray iron Fittings, 3 Inches through 48
Inches, for
Water Table
P2904.6, Table R4413.2.7
C511—00 Reduced Pressure Principle
Backflow Prevention Assembly Table P2902.2, P2902.2.5,
P2902, P2902.4.1
CGSB Canadian General Standards Board
Standard Referenced
in code
reference
number Title
section number
37–GP—52M—(1984) Roofing and
Waterproofing Membrane, Sheet Applied, Elastomeric R905.12.2, R4402.4.2.4
CISPI Cast Iron Soil Pipe Institute
Standard Referenced
in code
reference
number Title
section number
301—04a Specification for Hubless
Cast Iron Soil Pipe and Fittings for Sanitary
Table P3002.1, Table P3002.2,
and Storm Drain, Waste
and Vent Piping Applications Table R4413.2.2, Table R4413.2.3,
Table R4413.2.4, Table R4413.2.5
CPSC Consumer Product Safety Commission
Standard
Referenced in code
reference
number Title
section number
16 CFR Part 1201—(2002) Safety Standard for Architectural
Glazing R308.1.1, R308.3, R4410.2.1.3,
R4410.2.3.1.2, R4410.2.4.2
CSA Canadian Standards Association
8501 East Pleasant
Standard
Referenced
in code
reference
number Title
section number
A257.1—03 Nonreinforced Circular Concrete Culvert, Storm Drain, Sewer
Pipe and Fittings Table R4413.2.4
A257.2—03
Reinforced Circular Concrete Culvert, Storm Drain, Sewer Pipe and
Fittings Table R4413.2.4
B137.2—02 PVC Injection moulded
Gasketed Fittings for Pressure Applications Table P2904.6, Table R4413.2.7
B181.1—02 Plastic Drain and Sewer Pipe Fittings Table R4413.2.2, Table R4413.2.3
B181.2—02 PVC Drain, Waste Vent Pipe Fittings Table R4413.2.2, Table R4413.2.3
B181.3—02 Polyolefin Laboratory Drainage System Table R4413.2.2, Table R4413.2.3
B182.2—02 PVC Sewer Pipe and Fittings (PSM Type) Table R4413.2.4, Table R4413.2.5
B182.4—02 Profile PVC Sewer Pipe and Fittings Table R4413.2.4, Table R4413.2.5
DHS/FEMA Department of Homeland Security
Federal
Emergency Management Agency
Standard
Referenced in code
reference
number Title
section number
FEMA-TB-2-08 Flood Damage-Resistant Materials Requirements
R322.1.8
FEMA
-TB-11—01
Crawlspace Construction for Buildings Located in Special Flood Hazard
Areas
R408.7
DOC/NIST Department of Commerce
National
Standard
Referenced in code
reference
number Title
section number
CS
236 Mat Formed Particleboard
R4409.1.4.6, R4409.2.1.6
PS 1— 09
Construction and Industrial Plywood R404.2.1, Table R404.2.3, R503.2.1,
R604.1, R803.2.1,
R404.21, Table R404.2.3, R503.2.1, R604.1, R803.2.1, R4409.1.4.6, R4409.2.1.2
PS 2— 10 Performance Standard for Wood–based
Structural–use Panels R404.2.1, Table
R404.2.3, R503.2.1,
R604.1, R803.2.1, R404.21, Table R404.2.3, R503.2.1, R604.1,
R803.2.1,
R4409.1.4.6, R4409.2.1.2
PS
56 Structural Glued
Laminated Timber
R4409.1.4.6
PS 20—05 American Softwood Lumber Standard R404.2.1, R502.1.1, R602.1.1, R802.1.1,
Table R404.2.3, R503.2.1, R604.1, R803.2.1, R4409.1.4.6, R4409.2.1.8
DOL/OSHA
Department of Labor
Occupational Safety
and Health Administration
Standard
Referenced in code
reference
number Title
section
number
29
CFR 1910 General Industry
Occupational Health & Safety Standards
R4403.7.3
29
CFR 1926 650(P) Excavation Safety Act R4404.1.1
FM Factory Mutual Global Research
Standards Laboratories
Department
1151
Standard
Referenced in code
reference
number Title
section number
4450—(1989) Approval Standard for Class 1 Insulated
Steel Deck Roofs—with Supplements
through July
1992
R906.1, R4412.1.3.2.5.2
4470
(1992) Approval Standard for
Class 1 Roof Covers R4402.2.1, R4402.4.1.1,
R4402.4.2.4
4880—(2005) American National Standard for
Evaluating Insulated Wall or Wall and
Roof/Ceiling Assemblies, Plastic
Interior Finish Materials, Plastic Exterior
Building Panels,
Wall/Ceiling Coating Systems, Interior or Exterior
Finish Systems R314.4, R314.6, R4412.1.3.1.4
FS
Federal Specification
TT
P 1536A (1975) Federal Specification for Plumbing Fixture Setting Compound P3003.4.5
TTC
555B Test Specification for Wind Driven Rain Infiltration Resistance R4402.12.6.3.1
NAAMM
National Association of Architectural Metal Manufacturers
Standard
Referenced in code
reference
number Title section
number
ANSI/NAAMM
MBG 5XX Metal Grating Manual
R4408.1.3
NFPA National Fire Protection Association
1 Batterymarch
Park
Standard
Referenced in code
reference
number Title section
number
259—08 Test Method for Potential Heat of Building
Materials. . . . . 2603.4.1.10, 2603.5.3, 2612.3.2.4.4, R314.5.7, R4412.1.3.2.4.4
286—11 Standard Methods of Fire Tests for
Evaluating Contribution of Wall and
Ceiling Interior Finish
to Room Fire Growth R314.4, R314.6, R315.4, R4412.1.3.1.4
NRCA
National Roofing Contractors Association
Standard
Referenced in code
reference
number Title section
number
P
0405 Roofing and Waterproofing
Manual, 5th Edition
R4402.2.1
RCSC Research Council on Structural
Connections
c/o Stanley D. Lindsey
& Associates Ltd.
RCSC Load
and Resistance Factor Design Specification for Structural Joints Using A325 and
A490 Bolts, 1988 R4408.1.3
SDI Steel Door Institute
MOC1 SDI
Manual of Construction with Steel Deck R4408.1.3
DDP Deck
Damage and Penetrations R4408.1.3
DDM02 Diaphragm
Design Manual R4408.1.3,
R4408.9.4
SDI, LRFD Design
Manual for Composite Beams and Girders with Steel Deck R4408.1.3
SPD2 Standard
Practice Details R4408.1.3
NO. 30 Steel
Deck Institute Design Manual R4408.1.3
SDI Steel Door Institute
c/o Wherry
Associates
ANSI A250.13—03 Testing and Rating of Severe
Windstorm Resistant Components for Swinging Door Assemblies R613.4.4.1
SJI Steel Joist Institute
SJI Standard Specifications, Load Tables
and Weight Tables for Steel Joists and Joist Girders R4408.1.3
SJI Structural Design of Steel Joist Roofs
to Resist Ponding Loads, Technical Digest No. 3 R4408.1.3
SJI Structural Design of Steel Joist Roofs
to Resist Uplift Loads, Technical Digest No. 9 R4408.1.3
SJI Vibration of Steel Joist Concrete Slab
Floors, Technical Digest No. 5 R4408.1.3
SJI Welding of Open Web Steel, Technical
Digest No. 8 R4408.1.3
SJI 60 Year Steel Joist Manual R4408.1.3
SSPC Society for Protective Coatings
SSPC
Paint 15 Steel Joist Shop Paint R4408.1.3
SSPC/AISC Guide to the Shop Painting of
Structural Steel R4408.1.3
SPRI
Single-Ply Roofing Institute
Standard
Referenced in code
reference number Title
section number
ES
1-98 Wind Design Standard for Edge
Systems Used with Low Slope Roofing Systems R903.3
STI Steel Tube Institute of
2000
WSTI/STI Manual of Cold Formed Structural
Steel Tube R4408.1.3
TECO Timber Company Inc.
PRP
133 Performance Standards
and Policies for Structural Use Panels R4409.1.4.8,
R4409.2.1.2
TPI Truss Plate Institute
Standard
Referenced
in code
reference
number Title
section number
BCSI 06
Guide to Good Practice for Handling, Installing
Restraining & Bracing of Metal Plate R502.1.3.2, 802.1.6.3,
WTCA Connected Wood Trusses
R4409.1.4.9, R4409.6.17.2.4.1, R4409.6.17.2.4.3
TPI 1—02 National Design Standard for Metal plate
connected Wood Truss Construction R502.1.3.1,
R502.1.3.2, R802.1.6.2, R802.2.9.1,
R4409.1.4.9,
R4409.6.17.2.1.1, R4409.6.17.2.2.8
UL Underwriters Laboratories, Inc.
Standard
Referenced in code
reference
number Title section
number
9—00 Standard for Fire Tests of Window
Assemblies
R4407.4.2.12.8
580—94 Test for Uplift Resistance of Roof
Assemblies
R4408.1.3, R4408.9.4.6
790—04 Tests for Fire Resistance of Roof
Covering Materials— with Revisions through July 1998 R902.1,
R4402.2.1,
R4402.5.1, R4409.1.4.10, R4402.12.1.2
1040—96 Fire Test of Insulated Wall
Construction—with Revisions through June 2001 R314.4, R314.6,
R4412.1.3.1.4
1715—97 Fire Test of Interior Finish Material
R314.4, R314.6,
R4412.1.3.1.4
DHS/FEMA Department of Homeland Security
Federal
Emergency Management Agency
Federal Center
Plaza
500 C Street,
SW
Washington, DC 20472
Standard
Referenced in code
reference
number Title
section
number
FEMA-TB-2-08 TB-2—93
Flood Damage-Resistant Materials Requirements
R322.1.8
FEMA
FIA-TB-11—01
Crawlspace Construction for Buildings Located in Special Flood Hazard
Areas
R408.7
Chapter 44: Referenced Standards. Revise to read as follows:
High Velocity Hurricane Zone. Add Chapter 44 from the 2010 Florida Building
Code, Residential
Chapter 44: High Velocity Hurricane Zone
See Chapter 44 – see HVHZ file
Appendix E: Manufactured housing used as dwellings. Change to read as follows:
Appendix
E: Chapter 9B-53, Standard for Mitigation of Radon in
Existing Buildings.
See Appendix E of the 2010
FBCR
Appendix F: Radon control methods. Change to read as follows:
Appendix
F: Chapter 9B-52,
See Appendix F of the 2010 FBCR.